- No.100s[System-related Error]
- No.200s[Memory-related Error]
- No.300s[Precheck-related Error]
- No.400s, 500s[Wrapper-related Error]
- No.600s[Applicator-related Error]
- No.700s, 800s, 1000s, 1900s[Printer-related Error]
- No.1500s[Detector-related Error]
- No.1600s[Scale-related Error]
- No.1800s,4200s[Dialog Selection-related Error]
Error Number |
Error Content |
|||
Normal |
P Type |
JW Type |
BR Type |
|
Wrapper is not connected |
||||
No response from wrapper |
||||
Problem caused on wrapper |
||||
Wrapper detected temporary blackout |
||||
Temporary blackout on console |
||||
No response from wrapper |
||||
Lift motor is abnormal |
||||
Motor for film feed is abnormal |
||||
Motor for film change is abnormal |
||||
Film driving motor is abnormal |
||||
Film driving motor is abnormal |
||||
Motor for back squeeze plate is abnormal |
||||
Motor for R/L squeeze is abnormal |
||||
Outfeed pusher motor is abnormal |
||||
Feeder motor is abnormal |
||||
Motor front feeder move is abnormal |
||||
Motor rear feeder move is abnormal |
||||
Feed bar motor is abnormal |
||||
Centering motor is abnormal |
||||
Lift change is abnormal |
||||
Outfeed change motor is abnormal |
||||
Film heater has problem |
||||
Something is stuck underneath of lift |
||||
Motor voltage is abnormal |
||||
Emergency stop has been pushed |
||||
Film remove cover is open |
||||
Film exchange cover is open |
||||
Front cover is opened |
||||
Infeed conveyor is out |
||||
Do not put your hands into the machine |
||||
Do not put your hands into the machine |
||||
Under labeller unit is out |
||||
Roller for under labeller is out |
||||
Machine is returning to standby position (0000) |
||||
Machine is returning to standby position (9999) |
||||
Product was not feeded |
||||
Film over error for the upper |
||||
Film over error for the lower |
||||
Film feeding error for the upper |
||||
Film feeding error for the lower |
||||
Film loading was failed on the upper |
||||
It missed to print underlabeller |
||||
Stock part is not ready |
||||
There is problem on wrapping controller |
||||
There is problem on wrapping controller |
||||
There is problem on wrapping controller |
||||
There is problem on seal heater |
||||
There is problem on seal heater |
||||
Wrong selection for big/small lift |
||||
Wrong tray against programmed tray |
||||
Feeder bar is not original position |
||||
Insert plate is not set for the upper |
||||
Insert plate is not set for the lower |
||||
Film is remaining (0001) |
||||
Film is remaining (0100) |
||||
Film is remaining (0101) |
||||
Cutter is not back to original position |
||||
Insert plate is not back to original position |
||||
Sensor for the back side of feeder is abnormal |
||||
Heater safety guard is up |
||||
Auxiliary for magnetic contact is abnormal |
||||
Product is on the lift |
||||
Film loading for the upper (0000) |
||||
Film loading for the lower (0001) |
||||
Film loading for the upper is completed (0000) |
||||
Film loading for the lower is completed (0001) |
||||
Film removal is completed |
||||
Problem on wrapping part |
||||
Sum value for receiving is abnormal |
||||
Writing for flash ROM is busy |
||||
Failed in writing in flash ROM |
||||
Problem on wrapping part |
||||
The feed bar motor error |
||||
The loading conveyer motor error |
||||
The timing conveyer motor error |
||||
Product is remaining inside of infeeder |
||||
It failed in taking product in |
||||
Cover for the infeed is open |
||||
There is no product waiting for infeed |
||||
It failed in transported to wrapper |
||||
Automatic infeeder is OFF |
||||
Automatic infeeder is not connected |
||||
Tray is placed in front |
||||
Shutter operation of PS-AI is abnormal |
||||
Preparing film set (0000) |
||||
Preparing film set (0001) |
||||
Film loading instructions (0000) |
||||
Film loading instructions (0001) |
||||